YLX-30-HP

PATNERSHIP

Yasalink is an active company that wants to develop on a macro level. You can contact us to request cooperation and representation.

+90 545 635 0849

YLX-30-HP Antenna With Mimosa C5x

YLX-30-HP  +  Mimosa C5x

This antenna consists of a 0.72 m  reflector, feeder, and antenna mounting bracket. The mounting bracket is designed for installation on the vertical pipe diameter of 35mm to 75mm. The precise antenna mounting bracket provides adjustment ranges of ±19° fine elevation and ±11° fine azimuth.

The installation, maintenance or removal of antenna systems requires qualified, experienced personnel. This installation instructions have been written for such personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. Yasalink disclaims any liability or responsibility for the results of improper or unsafe installation practices.

Tools Required

ItemContentsQtyImage
1Combination Wrench, 13mm1Combination Wrench
2Screwdriver, cross-recess1Screwdriver
Item Contents Qty Image
A Reflector 0.52m & Mounting 1 Reflector 0.72m & Mounting
B Feeder 1 Feeder
C Transition 1 Transition
D Radio C5X 1 C5x
E Screw M4x12, Cross, st 4 Screw-Spring Washer
F Spring Washer M4, st 4
G Washer M4, st 4
H Screw M4x4, Allen, st 1 Screw
I Oring 2.5x50 1 Oring 2.5
J Oring 1.5x48 1 Oring 1.5
K Installation Guide 1

Installation

1- Install Feed to Reflector

Install Feed [B] to Reflector [A] by:
[E] Screw M4x12; 4 pcs
[F] Spring Washer M4; 4 pcs
[g] Washer M4; 4 pcs

YLX-30-HP-Attach Transition to Radio
2- Attach Transition to Radio

Install Transition [C] to Radio [D] by:
[I] Oring 2.5x50; 1 pcs

YLX-30-HP-Adjust Radio to Antenna
3- Adjust Radio to Antenna

Install Transition [C] & Radio [D] to Feed [B] by:
[H] Screw M4x4, Allen; 4 pcs
[J] Oring 1.5x48; 2 pcs

YLX-30-HP-Attach Antenna to Mounting Pole
4- Attach Antenna to Mounting Pole

Follow the picture to attach antenna to mounting pole then place the U-bolts on the M8x120 Screws and tighten M8 nuts.

YLX-30-HP-Adjust Azimuth and Elevation
5- Adjust Azimuth and Elevation

After an approximate alignment, both the elevation and azimuth could be precisely adjusted by tightening/loosening the elevation and azimuth screws shown in picture.
When azimuth/elevation are set, tighten all nuts to approximately 14N-m (10 lb-ft).

TECHNICAL DATA SHEET

General Specifications

  • Model Number : YLX-30-HP
  • Diameter (m) : 0.72
  • Polarization : Dual-slant 45°

Mechanical Specifications

  • Weight With Holder (kg) : 5.5 kg
  • Color : Metallic Red
  • Plating  :  Dacromet 
  • Screws and Nuts : Dacromet 
  • Fine Azimuth Adjustment : ±11°
  • Fine Elevation Adjustment : ±19°
  • Wind Loading (km/h) : 200
  • Operating Temperature : -40 °C to 60 °C
  • Supportable Comparative Damp : 90%

Electrical Specifications

  • Input : 2 × N-Female
  • Frequency Range (MHz) : 4.5 GHz to 5.5 GHz
  • VSWR : 1.4:1
  • Impedance (Ω) : 50
  • Gain (dBi) : 30
  • 3dB Beamwidth : H-plane: 5° / E-plane: 5°
  • F/B Ratio (dB) : 40
Patterns
YLX-30-HP-E-Plane
YLX-30-HP-H-Plane